Tecsun PL-600 Review

I have had the Tecsun PL-600 for 2 years now, so I thought it timely to do a review. 2 years gives one a chance to really get to know a receiver, work out it’s foibles etc., etc. This review is therefore from a users perspective and I shall not be covering every available function. Other sites have done an excellent job already on these points.

The Tecsun PL-600 is a portable receiver with LW, MW, FM and SW bands. Out of the box it comes with a nice padded travelling pouch, an antenna on a reel, 4 NiMH batteries, a wall-wart charger, earbud-style headphones and the manual. Everything is packed well and I purchased my particular example from an ebay seller in Scotland.

The specifications for the radio are as follows:

LW 100-519 kHz

MW 522-1620 kHz

SW 1711-29999 kHz

FM 87-108 MHz

So the shortwave bands, which will be the main subject of this review, are well covered with no breaks. In fact there is almost continuous coverage from 100 Khz to 29999 Khz.

I haven’t used the receiver on MW or LW as my interests do not lie in these areas. FM on local and national stations gives very good reproduction through the speaker or in full stereo if used with appropriate headphones.

For a while at this QTH, the main station receiver has been a Yaesu FRG-7, a venerable oldie from the ’70’s. While the ‘Frog’ is very good, I found it increasingly annoying that the dial calibration is not consistent end-to-end (a facet of the square-law function of a variable capacitor), and no narrow filter. The 6 Khz filter is fine for general listening but not useful for either ham-band SSB and CW or removing ACI on the broadcast bands.

So I have been using the ‘600 more and more and find it is now my main radio. Why?

Well, it has digital readout, it has memories, although I seldom use these, and it has a wide/narrow filter. The latter 2 settings I estimate being 6 Khz and 4 Khz. The narrow setting is great for removing ACI and has helped me a number of times to locate a station next to a higher powered one. The narrow setting is also selected automatically when SSB mode is engaged. The receiver also has a 3 position attenuator, which can be useful for strong stations, or indeed to cut down on noise.

Ergonomically, I think this receiver is well designed. It has a tilting attachment at the back which slants the radio at an ideal angle for desk top use. All the controls are easy to find and intuative, with push buttons, a keypad and a knob for tuning. So to select a station, one can either manually tune using the knob, use the up/down keys or directly key-in a frequency using the key pad. Tuning can be set at 5 Khz or 1 Khz, the latter useful for Ham stations or off-standard BC stations. With the SW button, the user can cycle through the broadcast bands, with an indication of which is selected display on the screen. One slightly annoying aspect of this is one can only scroll UP the bands and not Down.

A quick note on SSB reception. On my version, out of the box, SSB reception was distorted on all but the quietest stations. This is a known problem with the ‘600. Fortunately, there are a number of clever folks out in internet-land who have got a fix for this problem. I asked our tech. guy at work to do mine and it consists of adding a 1K resistor between pin 18 and ground of the audio amp chip. This simple mod transforms the audio on SSB. No more distortion and Ham band listening becomes a pleasure. So if you are thinking of or already have a ‘600 then this mod is well worth getting done.

I mainly use my ‘600 with an outdoor antenna, this being a 15 metre long wire fed through a homebrew 9:1 balun. Now some users have reported the ‘600 over-loading easily on an external antenna but I have never found this to be the case. It should be noted that the receiver is extremely capable on the built-in telescopic whip, which brings in numerous stations and I have used it this way for some garden ham-band and shortwave bc listening. The whip also swings round so that if the receiver is being used with the back tilt, the antenna can still be vertical.

There are some timer options available for setting alarms etc but I have never used these so cannot comment on their usefulness or otherwise.

The radio can be charged via the supplied charger, connection being via a power socket on the side of the receiver (not USB). The set of batteries supplied with the receiver were only 900 mAH versions and tended to run down fairly quickly, as even when the receiver is off, certain aspects of the display are still in operation. These batteries finally stopped holding any charge just recently and I switched to Sanyo Eneloop batteries, these being rated at 1900 mAH. These Eneloop batteries have a deserved reputation for longevity and charge cycles. So far the set I installed have lasted for over 2 weeks of near daily use.

So to some up. The Tecsun PL-600 is an extremely capable receiver, which can be used as a portable as well as a desk-top receiver. I think it’s good enough to use as a daily receiver for shortwave dx-ing and I would highly recommend it to anyone who is looking for a low-cost high quality radio. No it won’t compete with an Icom R-75, or CommRadio CR-1A but then those receivers are nearly 10 times the price.



4 thoughts on “Tecsun PL-600 Review

  1. Gerhard Stroebel

    Iwas given this PL600 three years ago and I I have also a Grundig Yacht Boy 500 and the performance was the same. I also have the Barlow Wadley (Same design as the Frog the Frog design is based on the Wadley loop) The only “Joke”in MHO is 600 stations presets I will have to keep a notebook to remember which station is on which preset makes them redundant.I was looking for a Short Wave receiver as they are scarce as “Hen’s teeth”here locally and when I was enquiring for one. because my Barlow Wadley was eating the audio amp I.C. it would play perfectly and suddenly for no reason would go short circuit and I could not source one affordable as I wanted one and if I wanted to get hold of one I had to buy 100 of them from wholesalers in U.S.A. and I am in South Africa!!!I have one gripe and that is ïmage”frequencies and it can only be cured with an external pre selector and this defeat the portability of the radio

    1. cendoubleu Post author

      Hi Gerhard

      Thanks for your comments. Yes, it is a shame that the 600 has the image problems, though to be fair, there are not many of them.
      I used the pre-selector as I haven’t used the receiver much as a portable and so that wasn’t a problem. I still think for the price point that it is amazing value for money.



    1. cendoubleu Post author

      Hi Laurence
      yes, like all hobbies, there can be a bewildering ‘language’ attached to it. DXing is just the act (process?) of looking for ‘DX’ or long distance/rare stations. A lot of these acronyms come from amateur radio and telegraph operators who predominately used morse code. It was their shorthand. A few more you may come across: QSB – fading; QRN – atmospheric noise; QRM – man-made noise.
      But don’t worry about the terminology, just tune the radio and see what you hear. I have published a post for beginners which you may care to view: https://shortwavelisteninguk.wordpress.com/2016/03/06/updated-beginners-guide-to-short-wave-listening/
      Good luck


Leave a Reply

Fill in your details below or click an icon to log in:

WordPress.com Logo

You are commenting using your WordPress.com account. Log Out /  Change )

Google+ photo

You are commenting using your Google+ account. Log Out /  Change )

Twitter picture

You are commenting using your Twitter account. Log Out /  Change )

Facebook photo

You are commenting using your Facebook account. Log Out /  Change )

Connecting to %s